Siemens SITRANS L Series Скачать руководство пользователя страница 66

Страница: 66 / 106

Setup with the integrated HMI

7.8.2 Peak values

Make sure that the material level is below all known installations when using

the

Auto false echo suppression wizard

to determine the TVT. Ideally the vessel

should be empty or almost empty.

Note the distance to the material level when determining the echo profile and

set the value in parameter "

Effective range of automatic false echo suppression

to a smaller distance to avoid suppression of the material echo.

If an agitator is used, it should be in operation.

Note

The effective range of the automatic false echo suppression sets the end point of the

determined TVT distance.

Determine the effective range of the automatic false echo suppression by measuring

the actual distance from the transmitter reference point to the material surface. Use

a cable or measuring tape.

Setting

Selection

Description

HOVER LEVEL

dB value of the basic noise

AFES ON

Activates the automatic auto

false echo suppression

AFES OFF

Deactivates the automatic

auto false echo suppression

SIGNAL

TVT CONFIG

AFES RANGE

Effective range of the

automatic false echo

suppression

7.8.2

Peak values

Min. measured distance

MIN DISTANCE:

Displays the value of the minimum measured distance. The value may reset if the

unit is changed.

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 66 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: