Siemens SITRANS L Series Скачать руководство пользователя страница 85

Страница: 85 / 106

Diagnostics and troubleshooting
12.3 Diagnosis, fault messages

• Signal processing

Fault rectification

The first measures are:
• Evaluation of fault messages
• Checking the output signal
• Treatment of measurement errors
A smart device (smartphone/tablet) with the adjustment app or a PC/notebook

with the PDM and the suitable EDD offer you further comprehensive diagnostic

possibilities. In many cases, the causes can be determined in this way and the faults

eliminated.

Reaction after fault rectification

Depending on the reason for the fault and the measures taken, the steps described

in chapter "

Setup

must be carried out again or must be checked for plausibility

and

completeness.

12.3

Diagnosis, fault messages

4 … 20 mA signal

Connect a multimeter in the suitable measuring range according to the wiring

plan. The following table describes possible errors in the current signal and helps to

eliminate them:

Error

Cause

Rectification

4 … 20 mA signal not

stable

Fluctuating measured value

Set damping

Electrical connection faulty

Check connection, correct, if

necessary

Voltage supply missing

Check cables for breaks; repair if

necessary

4 … 20 mA signal missing

Operating voltage too low, load

resistance too high

Check, adapt if necessary

Current signal greater

than 22 mA, less than

3.6 mA

Transmitter electronics defective

Replace device or send in for repair

depending on device version

12.4

Status messages according to NE 107

The transmitter features self-monitoring and diagnostics according to NE 107 and

VDI/VDE 2650. In addition to the status messages in the following tables there are

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 85 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: