Siemens SITRANS L Series Скачать руководство пользователя страница 19

Страница: 19 / 106

Description
3.4 Packaging, transport and storage

Transmitter

HART resistance 250 Ω (optional depending on evaluation)

Control system

Handheld

Figure 3.4

Connecting the PC to the signal cable

3.4

Packaging, transport and storage

Packaging

Your transmitter was protected by packaging during transport. Its capacity to handle

normal loads during transport is assured by a test based on ISO 4180.
The packaging consists of environment-friendly, recyclable cardboard. For special

versions, PE foam or PE foil is also used. Dispose of the packaging material via

specialised recycling companies.

Transport

Transport must be carried out in due consideration of the notes on the transport

packaging. Nonobservance of these instructions can cause damage to the device.

Transport inspection

The delivery must be checked for completeness and possible transit damage

immediately at receipt. Ascertained transit damage or concealed defects must be

appropriately dealt with.

Storage

Up to the time of installation, the packages must be left closed and stored according

to the orientation and storage markings on the outside.

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 19 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: