Siemens SITRANS FX330 Скачать руководство пользователя страница 87

Страница: 87 / 116

OPERATION

SITRANS FX330

www.siemens.com/flow

05/2016 - A5E36751269-AA

Status
type

Event group

Single event

Description

Actions to eliminate the
event

Sensor

Fatal Sensor Error

An internal error in the

sensor module has occured.

Perform a hard reset. If the

message recurs, contact the

manufacturer.

No Temperature Sensor

The internal temperature

sensor (PT1000) is not

connected or its resistance

is too high. The process

temperature cannot be

measured.

Check the pick-up and its

connection. Contact the

manufacturer, if necessary.

Sensor Comm. Error

Error in the internal bus

communication or hardware

failure.

For remote version: Check

the sensor connection.

Perform a hard reset. If the

message recurs, contact the

manufacturer.

No/Invalid Pressure Sensor

Pressure sensor not

available or invalid

communication

Check the connection of the

pressure sensor. Perform a

hard reset. If the message

recurs, contact the

manufacturer.

Corrupt Sensor Parameter

Flow sensor parameters are

inconsistent

Check flow sensor

parameters.

Temperature Sensor Error

The resistance of the

internal temperature sensor

(PT1000) is too low.

Check the pick-up and its

connection. Perform a hard

reset. Contact the

manufacturer, if necessary.

No Measurement Value

No connection to flow

sensor

Contact the manufacturer.

Electronics

Fatal Converter Error

An electronics or hardware

failure has occured.

Perform a hard reset. If the

message recurs, contact the

manufacturer.

CO DM Error

Internal electronic failure

CO DDM Error

Internal electronic failure

CO Unknown Error

Internal electronic failure

CO ADC Error

Internal electronic failure

Internal Comm. Error

Error in the internal bus

communication.

Inconsistent Parameters

Inconsistent data in the

parameter memory after
editing via HART

interface

Check the parameters and

make sure that the set of

data is consistent. Additional

information on the error can
be called via HART

interface.

Sensor Comm. Error

Error in the internal bus

communication or hardware

failure

Perform a hard reset. If the

message recurs, contact the

manufacturer.

Power Supply Error

Internal voltage too low to

switch on sensor power

supply

Check power supply

connection or replace the

electronics.

Sensor/Conv. FW Mismatch

Incompatible firmware

versions in the sensor and

the converter module

Perform a hard reset. If the

message recurs, contact the

manufacturer.

Max. Number of Restarts

The device could not start

the measuring mode after a

cold starting.

Perform a hard reset once

again. If the message

recurs, contact the

manufacturer.

Содержание SITRANS FX330





















































































































Результаты поиска

Содержание SITRANS FX330

Отзывы:

Siemens SITRANS FX330, Руководство по эксплуатации, Страница: 87 / 116

Результаты поиска

Содержание SITRANS FX330

Отзывы: