Siemens SITRANS FX330 Скачать руководство пользователя страница 78

Страница: 78 / 116

OPERATION

SITRANS FX330

www.siemens.com/flow

05/2016 - A5E36751269-AA

Function

Setting / Description

C3 Communication

C3.1 HART

C3.1.1 Current Loop Mode

Select: On (enables primary variable to be transmitted as 4

…

20 mA current values) /

Off (disables 4

…

20 mA transmission, but enables HART

multi-drop mode)

C3.1.2 Identification

HART

Identification parameters

C3.1.2.1 Polling Address

Set address for HART

operation. Standard setting is 000 for point-to-point operation

with current output 4

…

20 mA. Setting of polling address

≠

000 causes a constant 4 mA

output and enables multi-drop mode.

Enter: 000

…

063

C3.1.2.2 Tag

Enter measuring point identifier (1

…

8 digits).

C3.1.2.3 Long Tag

Enter long measuring point identifier (1...32 digits).

Entry will be displayed in the header bar on the LC display (depending on letter size,

min. 11 digits can be displayed).

C3.1.2.4 Manufacturer ID

HART

Manufacturer ID = 00042 (0x2A) [SIEMENS] (read-only)

C3.1.2.5 Device Type

Device Type = 00058 (0x3A) (read-only)

C3.1.2.6 Device ID

Individual device ID (read-only)

C3.1.2.7 Universal Revision

HART

revision (read-only)

C3.1.2.8 Device Revision

(read-only)

C3.1.2.9 Software Revision

(read-only)

C3.1.2.10 Hardware Revision

(read-only)

C3.1.3 Device Information

Informative text can be added to describe the device in the HART

communication loop.

C3.1.3.1 Descriptor

Commenting text to label instrument can be added; 1

…

16 digits.

C3.1.3.2 Message

Here additional information can be added.

C3.1.3.3 Date

Customer-defined date can be set here.

C3.1.3.4 Cfg. Change Counter

Counter for changes in settings (read-only).

C3.1.4 HART Variables

Definition of HART

variables.

C3.1.4.1 Current Out. Meas.

Primary HART

variable; identical with current output measurement variable.

C3.1.4.2 Frequency Out.

Meas.

Secondary HART

variable; identical with frequency output measurement variable. If

binary output is not activated or not configured as frequency output, the secondary
HART

variable is selectable. The variable selection is depending on the device

configuration.

C3.1.4.3 Current Input Meas.

Tertiary HART

variable; identical with current input measurement variable. If the

current input is not activated, the secondary HART

variable is selectable. The variable

selection is depending on the device configuration.

C3.1.4.4 Quaternary HART

Select (Availibility depending on fluid and medium configuration): Volume Flow / Norm.

Volume Flow / Mass Flow / Gross Power / Net Power / FAD / Volume / Norm. Volume /

Gross Energy / Net Energy / Density / Temperature1 / Temperature2 / Pressure /

Vortex Frequency / Velocity / Specific Enthalpy / Specific Heat Capacity / Reynolds

Number

C3.1.5 Catch DV Temp.

Catch device variable allows for capturing process data from another field device in a

multidrop network.

C3.1.5.1 Capture Mode

ACK - listen to responses by a specific slave device

BACK - listen to bursts by a specific slave device

OFF - disable capture mode

C3.1.5.2 Exp. Device Type

Define expanded device type for source slave.

Enter: 000

…

65535

Содержание SITRANS FX330





















































































































Результаты поиска

Содержание SITRANS FX330

Отзывы:

Siemens SITRANS FX330, Руководство по эксплуатации, Страница: 78 / 116

Результаты поиска

Содержание SITRANS FX330

Отзывы: