manualshive.com logo in svg

Siemens SITRANS FX330, Руководство по эксплуатации, Страница: 29 / 116

Поделиться
Скачать
Siemens SITRANS FX330 Скачать руководство пользователя страница 29

 INSTALLATION 

3

29

SITRANS FX330

www.siemens.com/flow

05/2016 - A5E36751269-AA

3.8  Installation

3.8.1  General installation notes

The following procedures have to be carried out before installing the device:

•  

Ensure that the gaskets have the same diameter as the pipelines.

•  

Note the correct flow direction for the device. This is indicated by an arrow on the neck of the 

flow sensor.

•  

On measuring points with varying thermal loads, the devices have to be mounted with stress 

bolts (DIN 2510).

•  

Stress bolts or bolts and nuts are not included in the scope of delivery.

•  

Ensure that the measuring flange is concentrically fitted.

•  

Note the exact installation length of the measuring device when preparing the measuring 

point.

CAUTION!

Installation, assembly, start-up and maintenance may only be performed by appropriately 
trained personnel. The regional occupational health and safety directives must always be 
observed.

Figure 3-10: Preparing the metering point

1  

Installation length of measuring  thickness of gaskets.

CAUTION!

The internal diameter of the pipelines, the flow sensor and the gaskets must match. The gaskets 
may not protrude into the flow.

Figure 3-11: Inner diameter

1  

Inner diameter of connection pipe

2  

Inner diameter of flange and gasket

3  

Inner diameter of flow sensor

Содержание SITRANS FX330





















































































































Отзывы:

Нет отзывов