Siemens SITRANS F US SONOKIT Скачать руководство пользователя страница 13

Страница: 13 / 95

SITRANS FUS080 transmitter
Operating Instructions, 07/2012, A5E03059912-02

Safety notes

CAUTION

Correct, reliable operation of the product requires proper transport, storage, positioning and

assembly as well as careful operation and maintenance. Only qualified personnel should

install or operate this instrument.

Note
Alterations to the product, including opening or improper modifications of the product, are not

permitted.
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.

2.1

Laws and directives

General requirements

Installation of the equipment must comply with national regulations. For example EN 60079-

14 for the European Community.

Instrument safety standards

The device has been tested at the factory, based on the safety requirements. In order to

maintain this condition over the expected life of the device, the requirements described in

these Operating Instructions must be observed.

NOTICE

Material compatibility
Siemens Flow Instruments can provide assistance with the selection of wetted sensor

parts. However, the full responsibility for the selection rests with the customer and Siemens

Flow Instruments can take no responsibility for any failure due to material incompatibility.

Содержание SITRANS F US SONOKIT
































































































Результаты поиска

Содержание SITRANS F US SONOKIT

Отзывы:

Siemens SITRANS F US SONOKIT, Руководство по эксплуатации, Страница: 13 / 95

Результаты поиска

Содержание SITRANS F US SONOKIT

Отзывы: