Siemens SITRANS F TRANSMAG 2 Скачать руководство пользователя страница 83

Страница: 83 / 126

Error

Diagnosis

Remedy

Device status (menu 2.1)
"Measurement module
failure"

Measuring range overflow

Reduce flow quantity or increase upper range val‐
ue in menu 3.1.2

Device status (menu 2.1)
"Measurement module"

Measuring electronics defective

Measurement with reduced accuracy still possi‐
ble; replace complete electronics

Defective immersion check

Deactivate immersion check (menu 2.3)

Magnetic field current outside the cali‐
brated range

Recalibrate unit

Fault in measuring function (incorrect
measuring frequency)

Turn off mains synchronization (menu 3.1.7.2).

Device status (menu 2.1)
"Calibration failure meas‐
uring module"

Self-test made with the result: measur‐
ing tolerances too high in relation to fac‐
tory calibration

Electronics must be recalibrated, send in device
(See chapter Return procedures)

Device status (menu 2.1)
"Simulation is running"

Device not in "Measure" status, Simula‐
tion is switched on

End simulation (exit the menu "Simulation" 2.5.2,
2.5.3 or 2.5.4 or select "End" in menu 2.5.1.
Alternatively: Restart the device

Device status (menu 2.1)
"Calibration is running"

Zero calibration (menu 6.6.2) started
and active

Device returns to measuring mode automatically
at the end of calibration

Device status (menu 2.1)
"Tube empty" (only possi‐
ble with immersion check :
menu 2.3) activated)

Measuring tube empty or only partially
filled

Fill measuring tube with medium, ensure it is
completely full

High percentage of gas

Clear gas occlusions or use gas trap

Device status (menu 2.1)
"Flow measurement un‐
certain"

Electrode DC voltage outside permitted
range

Clean sensor electrodes

Device status (menu 2.1)
"Measuring range over‐
flow"

Current flow too high

Reduce flow

Full scale value set too low

Increase upper range value in menu 3.1.2 or re‐
duce flow rate

Troubleshooting

10.3 Error messages

TRANSMAG 2 with MAG 911/E
Operating Instructions, 03/2021, A5E00102775-AC

Содержание SITRANS F TRANSMAG 2































































































































Результаты поиска

Содержание SITRANS F TRANSMAG 2

Отзывы:

Siemens SITRANS F TRANSMAG 2, Руководство по эксплуатации, Страница: 83 / 126

Результаты поиска

Содержание SITRANS F TRANSMAG 2

Отзывы: