manualshive.com logo in svg

Siemens SITRANS F FS200 Utility, Руководство по программированию, Страница: 35 / 36

Поделиться
Скачать
Siemens SITRANS F FS200 Utility Скачать руководство пользователя страница 35

Glossary

SNR

[Signal to Noise Ratio]. Represents a measure of SNR of the digitized acoustic

receive signal. Higher is better, typically values above 20 are desirable.

Status

Error code that is triggered by instantaneous acoustic signal problems. A

"Measurement" Status indicates that the meter is satisfied with the acoustic receive

signal and producing proper flow measurement readings.

Up and Dn

Indicates the upstream or downstream direction of acoustic signal transmission. Also

represents placement of flow sensors relative to flow direction for the purpose of identifying

“Forward” and “Reverse” flow directions.

VFmax

The flow rate that would create exactly 1-cycle (360°) of phase shift between the Upstream

and Downstream receive signals. This value is useful for the setting of the “HF” parameter

in gas applications, as it is necessary to do so at a flow rate that is higher than VFmax.

VoS

Velocity of Sound in the fluid medium. Shown in meter-selected measurement units of
either Feet/second (FPS) or Meters/second (M/S).

FS2

0

0 Programming Manual, 03/2020,

 

A5E02951525-AB

3

5

Содержание SITRANS F FS200 Utility





































Отзывы:

Нет отзывов