manualshive.com logo in svg

Siemens SITRANS F FS200 Utility, Руководство по программированию, Страница: 27 / 36

Поделиться
Скачать
Siemens SITRANS F FS200 Utility Скачать руководство пользователя страница 27

Utility Screens

Application Problems Tab

1. If any of your entered application parameters conflict with performance capabilities of

the FS230 flowmeter an “Application Problem” message will appear at the bottom of

the sizing screen; this will cause an additional tab to open [Application Problems] (See

Figure 6-8 below). Click on the tab to view a description of the conflict(s). If no conflicts

are present the tab will not appear.

Figure 6-8 Gas Application Problems Screen

2. A list of possible application conflicts and corrective actions appear in Table 4.1 below.

Application Warning

Corrective Action

Pipe diameter too small for selected sensor.

Allow FS200 to specify sensor

Flow velocity exceeds limit of installation.

 Programmed (Max) Flow too high verify entered value

Accuracy limitation at minimum velocity.

Programmed Min Flow below 1 FPS

Temperature above sensor limits.

Specified temperature exceeds 250F / 121C

Temperature below sensor limits.

Specified temperature below -40F/C

Poor sensor match to pipe wall.

Incorrect sensor selection, allow FS200 to select

Poor diameter-to-wall thickness ratio.

Pipe OD to wall ratio <10 to 1, may reduce performance

Excessive wall thickness.

Wall Thickness >1.25” Require Universal sensor

Pipe diameter must be greater than 1 inch / 25.4mm   Pipe OD must be greater than 1”/ 25.4mm for gas
Pressure may be too low for clamp-on.

Specified pressure below minimum, increase pressure

Carbon dioxide mole % too high.

CO2 mole % must be <10%

H2S mole % to high.

H2S mole% must be <20%

Table 6-1

Typical Gas Application Problems

FS2

0

0 Programming Manual, 03/2020,

 

A5E02951525-AB

27

Содержание SITRANS F FS200 Utility





































Отзывы:

Нет отзывов