manualshive.com logo in svg

Siemens SITRANS F FS200 Utility, Руководство по программированию, Страница: 32 / 36

Поделиться
Скачать
Siemens SITRANS F FS200 Utility Скачать руководство пользователя страница 32

32

Utility Screens

A list of possible application conflicts and corrective actions appear in Table 6-2 below.

Application Warning

Corrective Action

Maximum Pipe Diameter Exceeded

Select larger (Universal) sensor

Pipe diameter too small for selected sensor.

Allow FS200 to specify sensor

Flow velocity exceeds limit of installation.

 Programmed (Max) Flow too high verify entered value

Accuracy limitation at minimum velocity.

Programmed Min Flow below 1 FPS

Temperature above sensor limits.

Specified temperature exceeds 250F / 121C

Temperature below sensor limits.

Specified temperature below -40F/C

Poor sensor match to pipe wall.

Incorrect sensor selection, allow FS200 to select

Poor diameter-to-wall thickness ratio.

Pipe OD to wall ratio <10 to 1, may reduce performance

Excessive wall thickness.

Wall Thickness >1.25” Require Universal sensor

Operation in or near Reynolds transition

Flows in transition region will impact accuracy

Table 6-2

Liquid Application Problems

FS2

0

0 Programming Manual, 03/2020,

 

A5E02951525-AB

Содержание SITRANS F FS200 Utility





































Отзывы:

Нет отзывов