Siemens SIMOTION TM15 Скачать руководство пользователя страница 48

Страница: 48 / 99

Commissioning

3.3 Synchronous mode

TM15 / TM17 High Feature Operating Manual

Commissioning Manual, 05/2009

3.3

Synchronous mode

Note
This chapter pertains only to systems with external drives since this type of drive must be

synchronized during configuration of PROFIBUS/PROFINET. Conversely, systems with

integrated drives (i.e., one using SIMOTION D or CX32) use an integrated PROFIBUS that is

pre-configured and synchronized.

The TM15 and TM17 High Feature terminal modules must operate isochronously with the

SIMOTION Motion Control System. This is achieved by exchanging sign-of-life signals.
Therefore, isochronous operation must be selected
●

for PROFIBUS both on the master (SIMOTION) as well as the slave (SINAMICS)

●

for PROFINET both on the master (SIMOTION) as well as the device (SINAMICS)

PROFIBUS procedure

To make this selection in SINAMICS:
1.

Right-click the SINAMICS component in the project tree.

In the drop-down menu, select the "Open HW Config" option.

Right-click the SINAMICS icon.

In the drop-down menu, select the "Object properties" option.

Figure 3-4

SCOUT - "DP Slave Properties" window

Select the "Isochronous operation" tab.

Select the "Synchronize drive with equidistant DP cycle" check box.

If synchronization is lost (due to multiple consecutive transmission disturbances or

interruption of the bus), a flag is set in the module's status word. Also, the module stops

operation and all outputs are set to 0 V level. The module automatically attempts to restore

the synchronization and to restart. This takes only a few position control cycle clocks if the

restart is successful.

Note
To ensure error-free operation, we recommend that you program a synchronous status

query in the user program before issuing control commands to technology objects or

read/write accessing modules via I/O access.

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды