manualshive.com logo in svg

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Поделиться
Скачать
Siemens SIMOTION TM15 Скачать руководство пользователя страница 31

 

Configuration/programming 

 

2.2 Configuring and programming TM1x modules 

TM15 / TM17 High Feature Operating Manual 
Commissioning Manual, 05/2009 

31

 

2.

 

Note that the addresses have been assigned automatically. These addresses are the 

logical start addresses of the module in the message frame. You must later add the offset 

values from the graphical configuration screen form to these addresses if you want to 

determine the addresses for the individual I/O channels. 

 

 

 

Note 
When a TM1x is reconfigured, the structure of its message frame is changed, thus 

necessitating a realignment with HW Config. This process will create new (modified) 

addresses for the inputs and outputs. In addition, the I/O address assignment of the 

technology object must be updated. 
Even if the operating mode of a measuring input is changed (once/cyclically), realignment 

with HW Config is required, although this does not generate any new (changed) 

addresses for the inputs and outputs. 

 

 

 

Note 
Before making changes in the configuration screen forms of the TM15/TM17 High 

Feature Terminal Modules, you must close the screen form for aligning the hardware (see 

figure above). 

 

Содержание SIMOTION TM15




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды