Siemens SIMOTION TM15 Скачать руководство пользователя страница 24

Страница: 24 / 99

Configuration/programming

2.2 Configuring and programming TM1x modules

TM15 / TM17 High Feature Operating Manual

Commissioning Manual, 05/2009

Table 2- 2

"Function" column: Options in the drop-down menu

Menu option

Description

Channel used as a digital input

DO (standard output

)

Channel used as:
- Digital output, or
- Output of the output cam (without high switching accuracy)

Measuring input

Channel used as an input of a measuring input

Output cam (fast output

)

Channel used as a fast output of output cam (with high switching

accuracy)

The output of the output cam is calculated by the SIMOTION technology object in the IPO

cycle clock or position control cycle clock. (That is, the resolution is one IPO cycle clock or

one position control cycle clock.)

The switching instant of the output of the output cam is calculated by the TM15. For this

reason, the resolution is less than the position control cycle clock.
The value in the "Offset" column will later be added to the module address when the

technology object is configured. The result will be the absolute address of the respective I/O

channel.
Depending on which function has been selected, you can switch between the input or output

using the symbol displayed under "Inverter".

Table 2- 3

"Inverter" column: Description of symbols

Symbol

Description

Signal not inverted

Inverted input

Inverted output

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды