Siemens SIMOTION TM15 Скачать руководство пользователя страница 29

Страница: 29 / 99

Configuration/programming

2.2 Configuring and programming TM1x modules

TM15 / TM17 High Feature Operating Manual
Commissioning Manual, 05/2009

2.2.4

Other information

Note
When parameters are reassigned for the I/O channels, the new parameters do not take

effect until you restart (power on or hot restart) the SINAMICS or SIMOTION D device.

Note
Additional information and parameter setting options are available in the project tree next to

"Configuration" and "Inputs/Outputs" (e.g. Control logic, diagnostics, etc.). However, this

information is most relevant for modules that are configured via BICO technology, e.g. for

TM31. These registers are irrelevant to the user in TM15 and TM17 High Feature.

Note
When you click "TM15_1" or "TM17_1" in the project tree, a number of parameters are

displayed at the bottom of the symbol browser window. These parameters are irrelevant to

the user.

Note
TM15 and TM17 High Feature with vector drives or servo drives

If DRIVE CLiQ cycle clocks ≠ 125 µs are used with vector drives, inaccuracies will occur

when detecting signals via the Measuring Input technology object or when outputting signals

via the Output Cam/Cam Track technology objects.
The same phenomenon may arise with servo drives if you set sampling times via p112 that

result in DRIVE CLiQ cycle clocks ≠ 125 µs.
In the case of vector drives, the DRIVE CLiQ cycle clock is calculated by the Control Unit

during ramp-up.

The SCOUT Engineering System must be aware of this DRIVE CLiQ cycle clock (p4099)

that is set automatically by the Control Unit.
The same phenomenon may arise with servo drives if sampling times are set via p112 that

result in DRIVE CLiQ cycle clocks ≠ 125 µs.
In such cases, you should proceed as follows:
1.

Carry out a project download.

Establish an online connection.

Upload to the SINAMICS drive. The updated p4099 parameter is read in as a result of the

upload.

Delete the Fast I/O configuration via SCOUT. Select the SIMOTION CPU in the project

tree and right-click to open the context menu. Delete the configuration with the menu Fast

IO > Delete Configuration.

Switch to SCOUT OFFLINE mode.

Carry out a HW Config alignment. SCOUT uses this procedure to calculate internal

system data that is required for outputting/detecting signals with a high level of position

accuracy.

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды