Siemens SIMOTION TM15 Скачать руководство пользователя страница 41

Страница: 41 / 99

Configuration/programming

2.7 Limitations of use

TM15 / TM17 High Feature Operating Manual
Commissioning Manual, 05/2009

If the TM15 or TM17 High Feature Terminal Module is operated on a DRIVE CLiQ line with a

cycle time less than 125 µs, communication with these modules is not possible.

Note
Exceeding the allowable number of Terminal Modules on a given DRIVE CLiQ line can

cause the DRIVE CLiQ interface to cease communication.

2.7.2

Maximum number of drive objects

The maximum permissible number of drive objects per SIMOTION D, SINAMICS CU, or

SINAMICS CX32 is dictated by the installed controller/control unit.
●

SIMOTION D4x5, SINAMICS CU320 or SINAMICS CX32:
maximum of 16 drive objects

●

SIMOTION D410 or SINAMICS CU310:
maximum of 5 drive objects

Examples of drive objects:
●

CU320 control unit

●

Closed-loop infeed

●

CX32 expansion module

●

Motor modules (one double motor module constitutes 2 drive objects)

●

TB30

●

TM modules

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды