Siemens SIMOTION P320-4 E Скачать руководство пользователя страница 126

Страница: 126 / 166

FAQs / error correction

Possible cause

Possible remedy

Error message on the

screen:
Operating system not found

● No operating system

present.

● Incorrect active boot

partition.

● Incorrect drive entries in

the SETUP.

Check whether one of the specified causes is present:

Wrong time and/or date on

the PC.

● Press <ESC> during the boot sequence to open BIOS Setup.

Detailed information on the BIOS setup can be found in the
section Starting Bios settings Hotplug Enabled - BIOS
Setup (Page 127).

● Set the time and date in the setup menu.

Although the BIOS setting is

OK, the time and date are

still wrong.

The backup battery is emp‐

ty.

Replace the backup battery.
See SIMOTION P320-4 E / P320-4 S Commissioning and

Hardware Installation Manual > Service and maintenances >

Replacing the backup battery.
If the problem cannot be resolved by replacing the battery, then

contact your technical support team.

UPS does not function.

The operating system does

not have a suitable driver for

the UPS.

Install a suitable driver; the correct driver can often be downloa‐

ded from the homepage of the device's manufacturer.
Note the SIMOTION P320-4 E / P320-4 S Commissioning and

Hardware Installation Manual > Power on and software installa‐

tion > Customer-specific software.

The display in the BIOS for

the PROFINET MAC ad‐

dress is incorrect

(00:00:00:00:00:00).

The correct MAC addresses can be taken from the rating plate

on the housing.
See also Device identification data (Page 79), Section MAC ad‐

dresses.

Troubleshooting/FAQs
8.1 Error correction

SIMOTION P320-4 E / P320-4 S

126

Manual, 03/2018, A5E36004933B

Содержание SIMOTION P320-4 E







































































































































































Результаты поиска

Содержание SIMOTION P320-4 E

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION P320-4 E, Руководство пользователя

Результаты поиска

Содержание SIMOTION P320-4 E

Отзывы:

Бренды по названию

Популярные бренды