Siemens SIMOTICS M-1PH818, Инструкции по эксплуатации и монтажу

Страница: 306 / 314

Operating instructions
K3G280-RR04-M9
Siemens AG PD LD Nbg.
Translation of the original operating instructions
Fig. 1: Example illustrating vibration measurement. The arrangement of
the sensors depends on the device concerned and the installation
situation.
6.2 Cleaning
NOTE
Damage to the device during cleaning
Malfunction possible
→ Do not clean the device using a high-pressure cleaner.
→ Do not use acid, alkali or solvent-based cleaning agents.
→ Do not use any pointed or sharp-edged objects for cleaning
6.3 Safety inspection
NOTE
High-voltage test
The integrated EMC filter has Y capacitors. The tripping current
is exceeded when AC testing voltage is applied.
→ Test the device with DC voltage when you perform the
legally required high-voltage test. The voltage to be used
corresponds to the peak value of the AC voltage required by
the standard.
What to check How to check How often What action?
Contact
protection
cover for
intactness or
damage Visual inspection At least every
6 months
Repair or
replacement of
device
Device for
damage to
blades and
housing Visual inspection At least every
6 months
Replacement of
device
Fastening the
cables Visual inspection At least every
6 months
Fasten
Fastening the
protective earth
terminal Visual inspection At least every
6 months
Fasten
Insulation of
cables for
damage Visual inspection At least every
6 months
Replace cables
Impeller for
wear/deposits/
corrosion and
damage Visual inspection At least every
6 months
Clean or
replace impeller
Tightness of
cable gland Visual inspection At least every
6 months
Retighten,
replace if
damaged
Abnormal
bearing noise acoustic At least every
6 months Replace device
Vibration test Vibration
measuring
device, start-up
or run-down
measurement Recommended
every 6 months Clean, re-
balance and if
necessary
replace impeller
6.4 Disposal
For ebm-papst, environmental protection and resource preservation are
top priority corporate goals.
ebm-papst operates an environmental management system which is
certified in accordance with ISO 14001 and rigorously implemented
around the world on the basis of German standards.
Right from the development stage, ecological design, technical safety
and health protection are fixed criteria.
The following section contains recommendations for ecological disposal
of the product and its components.
6.4.1 Country-specific legal requirements
NOTE
Country-specific legal requirements
Always observe the applicable country-specific legal
regulations with regard to the disposal of products or waste
occurring in the various phases of the life cycle. The
corresponding disposal standards are also to be heeded.
6.4.2 Disassembly
Disassembly of the product must be performed or supervised by
qualified personnel with the appropriate technical knowledge.
The product is to be disassembled into suitable components for disposal
employing standard procedures for motors.
WARNING
Heavy parts of the product may drop off. Some of the
product components are heavy. These components
could drop off during disassembly.
This can result in fatal or serious injury and material damage.
→ Secure components before unfastening to stop them falling.
6.4.3 Component disposal
The products are mostly made of steel, copper, aluminum and plastic.
Metallic materials are generally considered to be fully recyclable.
Separate the components for recycling into the following categories:
●
Steel and iron
●
Aluminum
●
Non-ferrous metal, e.g. motor windings
●
Plastics, particularly with brominated flame retardants, in accordance
with marking
●
Insulating materials
●
Cables and wires
●
Electronic scrap, e.g. circuit boards
Item no. 55770-5-9970 · ENU · Change 94618 · Approved 2017-06-12 · Page 12 / 13
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
306