Siemens SENTRON PAC2200 Скачать руководство пользователя страница 82

Страница: 82 / 130

Service and maintenance

7.4 Troubleshooting guide

PAC2200

Equipment Manual, 12/2019, L1V30415167B-03

7.4

Troubleshooting guide

Remedies for the resolution of faults

Fault

Remedies

Device is not working



Check power supply



Check fuse

Voltage or current measured values are not displayed



Check fuse



Check configuration (see Parameterizing the device

(Page 64))

Voltage values are not plausible



If current transformer is available, check the settings and the

connection of the current transformer and correct if neces-

sary

Current values are not plausible



Check the settings and the wiring of the current transformer

(if present) and correct if necessary

No communication



Check the communication settings (incorrect IP address,

incorrect subnet, incorrect Modbus TCP port or gateway?)



Check firewall, if present (possibly preventing communica-

tion to the Modbus ports)

Power values are incorrect, although voltage and current

are correctly applied



Check voltages and currents of the phases (not properly

connected to one another)



Check the polarity of the current transformer, if present

Fault indication in the display menu:
kWh export
T1 + T2 kWh
SECONDARY
"MID VOID"



The device is defective and cannot be repaired.



The device may no longer be used for billing.

If the device fault cannot be remedied by the measures given above, the device is probably

defective.
More help can be found on the Internet.
Technical Assistance (

https://www.siemens.com/lowvoltage/support-request

)

If the device is defective, please proceed as follows:

●

See chapter Warranty (Page 81), if the device has become defective within the warranty

period.

●

If the device has become defective outside the warranty period, then the device must be

disposed of in accordance with local disposal regulations.

Содержание SENTRON PAC2200



































































































































Результаты поиска

Содержание SENTRON PAC2200

Отзывы:

Siemens SENTRON PAC2200, Руководство по эксплуатации продукта, Страница: 82 / 130

Результаты поиска

Содержание SENTRON PAC2200

Отзывы: