Siemens SENTRON PAC2200 Скачать руководство пользователя страница 49

Страница: 49 / 130

Connection

4.3 Connection examples

PAC2200
Equipment Manual, 12/2019, L1V30415167B-03

Connection examples for the 5 A device

CAUTION

Protection of the voltage measuring inputs
On the 5 A device, the fuses in the voltage measuring inputs are only used for cable

protection. Selection of the fuse depends on the supply cable dimensioning. All

commercially available fuses and automatic circuit breakers up to 16 A (C) or 20 A (B) can

be used. The relevant applicable regulations must be complied with in selecting the fuse.

(1) Three-phase measuring, four conductors, unbalanced load, with three current

transformers
Connection type 3P4W

The fuses in the voltage measuring inputs are only used for cable protection.

Figure 4-3

Connection type 3P4W, with three current transformers

(2) Single-phase measuring, with one current transformer
Connection type 1P2W

The fuses in the voltage measuring inputs are only used for cable protection.

Figure 4-4

Connection type 1P2W, with one current transformer

Содержание SENTRON PAC2200



































































































































Результаты поиска

Содержание SENTRON PAC2200

Отзывы:

Siemens SENTRON PAC2200, Руководство по эксплуатации продукта, Страница: 49 / 130

Результаты поиска

Содержание SENTRON PAC2200

Отзывы: