Siemens SENTRON PAC2200 Скачать руководство пользователя страница 76

Страница: 76 / 130

Commissioning

6.3 Parameterizing the device

PAC2200

Equipment Manual, 12/2019, L1V30415167B-03

"Communication" parameter

The number of available communication interfaces can vary depending on the version of the

device.

"MODBUS TCP" parameter (optional)
The "MODBUS TCP" parameter is only available for devices with an Ethernet interface.

Selection

Range

Factory setting

MAC

MAC address. Read only.

–

DHCP

(Dynamic Host Configuration Protocol)
OFF
ON
If the DHCP is activated, network configurations are

automatically assigned. This enables automatic inte-

gration of devices into an existing network. If the

DHCP is activated, network configurations cannot be

adjusted manually.

IP address: 000.000.000.000
Manual setting of the IP address is only possible when

DHCP is deactivated.

–

SN
(subnet mask)

Subnet address: 000.000.000.000
Manual setting of the subnet is only possible when

DHCP is deactivated

–

LIMIT
(gateway)

Gateway address: 000.000.000.000
If data exchange with an IP address which is not in the

home subnet is required, the data can be transmitted

via a gateway. Gateway interconnects different net-

works.
Manual setting of the gateway is only possible when

DHCP is deactivated.

–

PORT

Modbus port: 0 to 65534

502

IP FILTER



OFF: IP filter deactivated



ON: Write access is rejected if the remote station is

in another subnet.

The IP filter, also called subnet firewall protection, is a

configurable protection on the device. If the protection

is activated, write requests are only accepted if the

user is in the same subnet.

OFF

HTTP PORT
(web server)

Manual setting of the HTTP port (web server): 0 to

65534
With the HTTP port 0 setting, the web server is deac-

tivated.

Содержание SENTRON PAC2200



































































































































Результаты поиска

Содержание SENTRON PAC2200

Отзывы:

Siemens SENTRON PAC2200, Руководство по эксплуатации продукта, Страница: 76 / 130

Результаты поиска

Содержание SENTRON PAC2200

Отзывы: