Siemens SENTRON PAC2200 Скачать руководство пользователя страница 18

Страница: 18 / 130

Description

2.1 Performance features

PAC2200

Equipment Manual, 12/2019, L1V30415167B-03

Tariff switching after synchronization
When synchronizing the average power demand values via the communication interfaces

or the digital input, the tariff change will only become effective after expiry of the

period. Without synchronization, the tariff change takes effect immediately.

The synchronization frame contains the length of the demand period in minutes. The

synchronization command is ignored if the period length sent to the device with the

synchronization frame is different to the length parameterized in the device.

MID-approved

MID-approved devices are included in the portfolio. These devices are suitable for billing the

active energy.
The following actions cannot be carried out on MID-approved devices:

●

FW update

●

Resetting the secondary energy values

●

Parameterization of the voltage input

●

Inversion of the direction of current flow

The secondary value of the total active energy is suitable for billing purposes.
The current transformer ratios set have no effect on the secondary total energy value.

The secondary total energy value may already display a counter value upon delivery as a

result of factory device testing.

Содержание SENTRON PAC2200



































































































































Результаты поиска

Содержание SENTRON PAC2200

Отзывы:

Siemens SENTRON PAC2200, Руководство по эксплуатации продукта, Страница: 18 / 130

Результаты поиска

Содержание SENTRON PAC2200

Отзывы: