Siemens SCALANCE X-200RNA Скачать руководство пользователя страница 36

Страница: 36 / 158

Autonegotiation

With the autonegotiation mechanism, repeaters and end devices can automatically determine

the transmission speed and the transmission mode of the partner interface. This makes it

possible to configure different devices automatically. Two components connected to a link

segment can exchange information about the data transfer and can adapt their settings to each

other. The mode with the highest possible speed is set.

Note
The SCALANCE X204RNA operates permanently in autonegotiation mode and can therefore

be connected to other devices that either also use the autonegotiation mode or the "100 Mbps

mode FD (full duplex)".

Note
The SCALANCE X204RNA is a plug-and-play device that does not require settings to be made

for commissioning.

MDI / MDI-X autocrossover function

The advantage of the MDI /MDI-X autocrossover function is that straight-through cables can

be used throughout and crossover Ethernet cables are unnecessary. This prevents

malfunctions resulting from mismatching send and receive wires. This makes installation much

easier for the user.
The SCALANCE X204RNA supports the MDI / MDI-X autocrossover function.

Note
Please note that the direct connection of two ports on the switch or accidental connection over

several switches causes an illegal loop. Such a loop can lead to network overload and network

failures.

Transmission speed

The transmission speed of the Fast Ethernet ports is 100 Mbps full duplex.

Descriptions of the products
4.4 SCALANCE X204RNA

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

Содержание SCALANCE X-200RNA































































































































































Результаты поиска

Содержание SCALANCE X-200RNA

Отзывы:

Бренды по названию

Популярные бренды

Siemens SCALANCE X-200RNA, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X-200RNA

Отзывы:

Бренды по названию

Популярные бренды