Siemens SCALANCE X-200RNA Скачать руководство пользователя страница 14

Страница: 14 / 158

General notices on use in hazardous areas

WARNING

Risk of explosion when connecting or disconnecting the device
WARNING – EXPLOSION HAZARD
DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR

COMBUSTIBLE ATMOSPHERE IS PRESENT.

WARNING

Replacing components
WARNING – EXPLOSION HAZARD
SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION

2 OR ZONE 2.

WARNING

Requirements for the cabinet/enclosure
When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone

2, the device must be installed in a cabinet or a suitable enclosure.

General notices on use in hazardous areas according to ATEX (SCALANCE X204RNA only)

WARNING

Requirements for the cabinet/enclosure
To comply with EC Directive 94/9 (ATEX95), this enclosure must meet the requirements of

at least IP54 in compliance with EN 60529.

WARNING

Suitable cables for temperatures in excess of 70 °C
If the cable or conduit entry point exceeds 70°C or the branching point of conductors exceeds

80°C, special precautions must be taken. If the equipment is operated in an air ambient in

excess of 50 °C to 70 °C, only use cables with admitted maximum operating temperature of

at least 80 °C.

WARNING

Protection against transient voltage surges
Take measures to prevent transient voltage surges of more than 40% of the rated voltage.

This is the case if you only operate devices with SELV (safety extra-low voltage).

Safety notices

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

Содержание SCALANCE X-200RNA































































































































































Результаты поиска

Содержание SCALANCE X-200RNA

Отзывы:

Похожие инструкции для SCALANCE X-200RNA

Бренды по названию

Популярные бренды

Siemens SCALANCE X-200RNA, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X-200RNA

Отзывы:

Похожие инструкции для SCALANCE X-200RNA

Бренды по названию

Популярные бренды