Siemens SCALANCE W748-1 Скачать руководство пользователя | Manualshive

Страница: 36 / 68

background image

Connecting up

5.2 Lightning protection, power supply and grounding

SCALANCE W788-x / W748-1

36

Operating Instructions, 09/2017, A5E03678333-12

5.2

Lightning protection, power supply and grounding

Lightning protection

WARNING

Danger due to lightning strikes
Antennas installed outdoors must be within the area covered by a lightning protection

system. Make sure that all conducting systems entering from outdoors can be protected by

a lightning protection potential equalization system.
When implementing your lightning protection concept, make sure you adhere to the VDE

0182 or IEC 62305 standard.

Suitable lightning protectors are available in the accessories (Page 15) of SIMATIC NET

Industrial WLAN.

Note
We recommend that you use the maintenance-free lightning protector LP798-2N.
Exception: When there is also DC power supplied via the antenna cable. In this case, only

the lightning protector LP798-1N can be used.

WARNING

Danger due to lightning strikes
Installing this lightning protector between an antenna and a SCALANCE W700 is not

adequate protection against a lightning strike. The LP798-1N lightening protector only

works within the framework of a comprehensive lightning protection concept. If you have

questions, ask a qualified specialist company.

Note
The requirements of EN61000-4-5, surge immunity tests on power supply lines, are met only

when a Blitzductor is used with 24 VDC:
BVT AVD 24

article number: 918 422

Manufacturer: DEHN+SÖHNE GmbH+Co.KG, Hans Dehn Str. 1, Postfach 1640, D -

92306 Neumarkt, Germany

«
...
34
35
36
37
38
...
»

Содержание SCALANCE W748-1





































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE W748-1

Бренд: FS Страницы: 12

Бренд: B-Link Страницы: 14

Бренд: Ruckus Wireless Страницы: 4

WGR612 - 54 Mbps Wireless Router

Бренд: NETGEAR Страницы: 2

Бренд: FS Страницы: 36

Бренд: Ebyte Страницы: 10

Бренд: Cranberry Страницы: 2

Бренд: Billion Страницы: 61

Бренд: Aerohive Страницы: 12

Бренд: Redline Страницы: 25

HAP 21001-Series

Бренд: Alpha IP Страницы: 48

Бренд: Tenda Страницы: 2

Бренд: E-Lins Страницы: 6

Бренд: Sapido Страницы: 112

Бренд: Planet Networking & Communication Страницы: 82

Бренд: Planet Networking & Communication Страницы: 93

Бренд: KTI Networks Страницы: 2

Бренд: BlueBOLT Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды