Siemens SCALANCE W748-1 Скачать руководство пользователя

Страница: 19 / 68

Description of the device

3.4 Accessories

SCALANCE W788-x / W748-1
Operating Instructions, 09/2017, A5E03678333-12

Flexible connecting cable IWLAN QMA/N-Connect male/female

Adapter cable for connecting a MIMO antenna with QMA connectors with the flexible

connecting cables. Preassembled with two connectors QMA male and N-Connect female.

pack of 3

Length

Article number

1 m

6XV1875-5JH10

For railway applications, the following connecting cable is available Note: Scope of delivery:

Pack of 1

Length

Article number

1 m

6XV1875-5VH10

3.4.1.2

Antennas

Note
When you select an antenna, keep in mind the national approvals for your device.
You will find more information in the following Link (

https://www.siemens.com/wireless-

approvals

)

The SCALANCE W786-2IA RJ-45 uses internal omni antennas (3/4 dBi at 2.4 GHz or 5

GHz).

Type

Properties

Article number

ANT792-4DN

RCoax helical antenna, circular polariza-

tion, 4 dBi, 2.4 GHz, N-Connect female.

6GK5792-4DN00-0AA6

ANT792-6MN

Omni antenna, mast/wall mounting, 6 dBi

2.4 GHz, N-Connect female

6GK5792-6MN00-0AA6

ANT792-8DN

Directional antenna, mast/wall mounting,

14 dBi 2.4 GHz, N-Connect female

6GK5792-8DN00-0AA6

ANT793-4MN

RCoax λ5/8 antenna with vertical polar

zation, 6 dBi, 5 GHz, N-Connect female.

6GK5793-4MN00-0AA6

ANT793-6DG

Wide angle antenna, mast/wall mount-

ing, 9 dBi 5 GHz, 2 x N-Connect female

6GK5793-6DG00-0AA0

ANT793-6DT

Wide angle antenna (MIMO), mast/wall

mounting, 8 dBi 5 GHz, 3 x QMA con-

nector female

6GK5793-6DT00-0AA0

ANT793-6MN

Omni antenna, mast/wall mounting, 5 dBi

5 GHz, N-Connect female

6GK5793-6MN00-0AA6

ANT793-8DJ

Directional antenna, mast/wall mounting,

18 dBi 5 GHz, 2 x N-Connect female

6GK5793-8DJ00-0AA0

ANT793-8DK

Directional antenna, mast/wall mounting,

23 dBi 5 GHz, 2 x N-Connect female

6GK5793-8DK00-0AA0

Содержание SCALANCE W748-1





































































Результаты поиска

Содержание SCALANCE W748-1

Отзывы:

Похожие инструкции для SCALANCE W748-1

Бренды по названию

Популярные бренды

Siemens SCALANCE W748-1, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE W748-1

Отзывы:

Похожие инструкции для SCALANCE W748-1

Бренды по названию

Популярные бренды