Siemens SCALANCE W748-1 Скачать руководство пользователя страница 20

Страница: 20 / 68

Description of the device

3.4 Accessories

SCALANCE W788-x / W748-1

Operating Instructions, 09/2017, A5E03678333-12

Type

Properties

Article number

ANT795-4MA

Omni antenna, directly on the device, 3/5

dBi 2.4 GHz and 5 GHz, IP30, R-SMA

connector male for direct mounting on

the device, connector angle adjustable

0° to 180°.

6GK5795-4MA00-0AA3

ANT795-4MC

Omnidirectional antenna, 3/5 dBi, 2.4

GHz and 5 GHz, IP65, N-Connect male

for direct installation on the device,

straight connector.

6GK5795-4MC00-0AA3

ANT795-4MD

Omnidirectional antenna, 3/5 dBi, 2.4

GHz and 5 GHz, IP65, N-Connect male

for direct installation on the device, 90°

connector.

6GK5795-4MD00-0AA3

ANT795-6DC

Wide angle antenna, mast/wall mount-

ing, 9 dBi 2.4 GHz and 5 GHz, N-

Connect female

6GK5795-6DC00-0AA0

ANT795-4MB

Omnidirectional antenna, 2/3 dBi 2.4

GHz and 5 GHz, IP30, R-SMA connector

female for direct mounting on the device,

connector angle adjustable 0° to 90°.

6GK5795-4MB00-0Ax0

ANT795-6MN

Omni antenna, mounted on roof/vehicle,

6/8 dBi 2.4 GHz and 5 GHz, N-Connect

female

6GK5795-6MN10-0AA6

ANT795-6MT

Omni antenna (MIMO), mounted on

roof/vehicle/ceiling, 5/7 dBi 2.4 GHz and

5 GHz, 3 x QMA connector female

6GK5795-6MT00-0AA0

ANT793-8DL

Directional antenna vertical-horizontal

polarized, 5 GHz, 14dBi, IP66, 2xN-

Connect female

6GK5793-8DL00-0AA0

ANT793-8DP

Directional antenna, mast/wall mounting,

13 / 13.5 dBi 4.9 GHz and 5 GHz, N-

Connect female

6GK5793-8DP00-0AA0

ANT795-4MX

Omnidirectional antenna, 2/2,5 dBi, 2.4

GHz and 5 GHz, IP69K, N-Connect male

6GK5795-4MX00-0AA0

ANT795-6MP

Omnidirectional antenna, 5/7 dBi, 2.4

GHz and 5 GHz, IP65/67, N-Connect

female

6GK5795-6MP00-0AA0

ANT896-6MM

Omnidirectional antenna for mobile wire-

less, WLAN and GPS, WLAN: 6/7 dBi,

2.4 GHz and 5 GHz, IP68, IP69 K, QMA-

Connect female, port 2

6GK5896-6MM00-0AA0

IWLAN RCoax Cable

2,4 GHz PE 1/2"

Omni antenna, 0 dBi 2.400 - 2.485 GHz,

N-Connect female.

6XV1875-2A

IWLAN RCoax Cable 5

GHz PE 1/2"

Omni antenna, 0 dBi 5.150 – 5.875 GHz,

N-Connect female.

6XV1875-2D

Содержание SCALANCE W748-1





































































Результаты поиска

Содержание SCALANCE W748-1

Отзывы:

Бренды по названию

Популярные бренды

Siemens SCALANCE W748-1, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE W748-1

Отзывы:

Бренды по названию

Популярные бренды