background image

 

SCALANCE W788-x / W748-1 
Operating Instructions, 09/2017, A5E03678333-12 

27

 

 

Mounting 

 

 

 

 

CAUTION 

Minimum distance to antennas 
Fit the device so that there is a minimum clearance of 20 cm between antennas and 

persons. 

 
 

 

WARNING 

If a device is operated in an ambient temperature of more than 50 °C, the temperature of 

the device housing may be higher than 70 °C. The device must therefore be installed so 

that it is only accessible to service personnel or users that are aware of the reason for 

restricted access and the required safety measures at an ambient temperature higher than 

50 °C. 

 
 

 

WARNING 

When used in hazardous environments corresponding to Class I, Division 2 or Class I, 

Zone 2, the device must be installed in a cabinet or a suitable enclosure. 

 

General notes on use according to ATEX and IECEx 

 

 

 

WARNING 

To comply with EC Directive 2014/34/EU (ATEX 114) or the conditions of IECEx, this 

enclosure or cabinet must meet the requirements of at least IP54 in compliance with EN 

60529. 

 

 

Содержание SCALANCE W748-1





































































Отзывы: