Siemens RUGGEDCOM WIN5237 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 42

background image

RUGGEDCOM WIN5237

Installation Guide

Chapter 2

Installing the Subscriber Station

Installing the Hazardous Location Kit

21

2

3

1

Figure 15: Assembling the Connector Components

1.

PoE Plug

2.

Plug Housing

3.

Dust Cover

15. Align the latch with the LATCH slot.
16. Press the plug into the plug housing until it bottoms out.
17. While maintaining inward pressure on the plug or keeping the dust cover engaged, tighten the compression

nut to 0.56 N·m (5 In-lbs).

Section 2.8.4

Installing the Hazardous Location Kit

An approved Power-over-Ethernet (PoE) injector is required when the subscriber station is installed in a hazardous

location. The RUGGEDCOM WIN5237 is certified for installation in Class I, Division 2 Groups A, B, C and D

hazardous locations when installed using the Class I, Division 2 kit (P/N MKIT0090). The Class I, Division 2 kit

contains the following items:
• Power supply unit
• PoE injector
• DC power cable
• Open-ended AC power cable
To install the subscriber station in a hazardous location, do the following:
1. Connect the DC power cable between the power supply unit and the PoE injector.

«
...
25
26
27
28
29
...
»

Содержание RUGGEDCOM WIN5237











































Отзывы:

Нет отзывов

Похожие инструкции для RUGGEDCOM WIN5237

Бренд: ABB Страницы: 66

Бренд: Maco Страницы: 38

Бренд: Salusfin Страницы: 6

Бренд: Tripp Lite Страницы: 20

Бренд: IDT Страницы: 281

DMX-Universal-Demux

Бренд: DMX4ALL Страницы: 17

Бренд: Rockwell Automation Страницы: 108

Бренд: TRENDnet Страницы: 2

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Бренд: Tait Страницы: 8

Бренд: C4i Страницы: 5

Бренд: THOMSON Страницы: 212

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

Бренд: Longshine Страницы: 35

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

Бренд: Patton Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды