Siemens RUGGEDCOM WIN5237 Скачать руководство пользователя страница 5

Страница: 5 / 42

RUGGEDCOM WIN5237

Installation Guide

Preface

Alerts

Preface

This guide describes the RUGGEDCOM WIN5237. It describes the major features of the subscriber station,

installation, commissioning and important technical specifications.
It is intended for use by subscriber station installers and operators, and assumes readers have a working

knowledge of WiMAX technologies and procedures. While some safety precautions are reviewed here, it is

assumed that installers are trained in safe installation practices. Users unfamiliar with safe installation procedures,

WiMAX technologies, and service procedures should not rely on this manual for comprehensive guidance.

CONTENTS

•

•

•

•

Alerts

The following types of alerts are used when necessary to highlight important information.

DANGER!

DANGER alerts describe imminently hazardous situations that, if not avoided, will result in death or

serious injury.

WARNING!

WARNING alerts describe hazardous situations that, if not avoided, may result in serious injury and/or

equipment damage.

CAUTION!

CAUTION alerts describe hazardous situations that, if not avoided, may result in equipment damage.

IMPORTANT!

IMPORTANT alerts provide important information that should be known before performing a procedure

or step, or using a feature.

NOTE

NOTE alerts provide additional information, such as facts, tips and details.

Содержание RUGGEDCOM WIN5237











































Результаты поиска

Содержание RUGGEDCOM WIN5237

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5237

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM WIN5237, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM WIN5237

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5237

Бренды по названию

Популярные бренды