manualshive.com logo in svg

Siemens POLYMOBIL III, Инструкция по эксплуатации, Страница: 35 / 42

Поделиться
Скачать
Siemens POLYMOBIL III Скачать руководство пользователя страница 35

Notes on trouble-shooting

4 - 23

Siemens AG

 

RXB8-115.061.02

Page 23 of 24

POLYMOBIL III

Medical Solutions

Rev. 01

10.95

CS PS 24

 

 

Checking and readjusting the counterweight

4

•

Unlock the support arm (1/Fig. 7) and release the turning knob (2/Fig. 7).
Without any accessories attached, the support arm should be easy to move across the 
entire movement range and stop in any position.

Readjusting the counterweight with accessories attached

4

If the support arm does not stop in any position with accessories attached, readjust the 
spring tension for the counterweight.

•

Take the cover (3/Fig. 7) off the stand.

•

Completely release the additional brake on the support arm (2/Fig. 7).

•

Move the support arm into the horizontal position.

•

Tighten the screw by means of a 17mm fork wrench (4/Fig. 8).
Adjust the spring tension so that the support arm is balanced in the horizontal position, 
i.e. the forces needed for lifting and lowering the tube unit are equal.

4

1

2

3

Fig. 7

Fig. 8

Содержание POLYMOBIL III











































Отзывы:

Нет отзывов