Siemens IM 328-N Скачать руководство пользователя страница 50

Страница: 50 / 86

07.96

Description

3-22

6ZB5 430–0BH02–1AA0



SINUMERIK 805SM / 840C (BS)

3.3

Description of the L2-DP slave up to V3.x

Note

This section only applies if

The IM 328–N module with the order number 6FC5 012–0CA01–0AA0
is used

The module with the order number 6FC5 012–0CA03–0AA0 is used and
jumper X999 is set for operation as a SINEC L2–DP slave up to V3.x
(see Section 2.1.1).

3.3.1

Notes on parameterization of the slave

Here are some notes on how to use the IM 328–N as an L2–DP slave up to
V3.x in the ET 200 Distributed I/O System.

For example, the master IM 308–B or IM 329–N can be used.

If the IM 308–B or IM 329–N module is the master, then

PG/PC with COM ET 200 (V4.x)

Note

About the system parameter BUS PROFILE:
Select one of the bus profiles
“DP up to V.3x”

No DP standard slaves and no FMS stations
(e.g. IM 328)

“DP standard”

DP Siemens slaves, standard slaves but not
FMS stations or

“DP/FMS”

DP Siemens slaves, standard slaves and FMS slaves.

With this setting, the bus profile is set for the entire bus (timeout settings
etc.).

About the baud rate:
Baud rates up to 1500 kBaud are possible.

Preconditions
for slave para-
meterization

ET 200
system parameters

3.3 Description of the L2-DP slave up to V3.x

Содержание IM 328-N























































































Результаты поиска

Содержание IM 328-N

Отзывы:

Похожие инструкции для IM 328-N

Бренды по названию

Популярные бренды

Siemens IM 328-N, Описание

Результаты поиска

Содержание IM 328-N

Отзывы:

Похожие инструкции для IM 328-N

Бренды по названию

Популярные бренды