background image

9 / 14

A6V10881143_en--_c

Siemens

2019-04-25

Smart Infrastructure

Commissioning

Parameterization

The following parameters must be checked or set prior to commissioning:

Parameter

Range

Description

Factory setting

Opening
direction

CW (R) / CCW (L)  

Opening direction of rotary actuator

CW (R)

Commissioning workflow 1: Full or partial configuration by tool

When using the AST20 handheld tool, all bus and actuator parameters can be set.

Connect the AST20 to the rotary actuator and navigate to the bus configuration menu

Set bus parameters as desired

Optionally make changes on actuator parameters.

Note

With AST20, all parameters can be set using the mass configuration function. The bus parameters are included in the
mass configuration function. It can be selected that the address is automatically incremented with each programmed
actuator.

Commissioning workflow 2: Configuration over bus (fully or partially)

The devices can be configured over bus if the pre-commissioning settings allow for a con-
nection between the Modbus master / programming tool and peripheral devices (i.e. non-
conflicting addresses and matching baudrate / transmission format).

Full configuration over bus: If the address is unique per segment when powered up, the
device can be accessed by the Modbus master (or programming tool) and the address
and other parameters can then be set to the definitive values.

Partial configuration over bus: If the address is not unique per segment when powered up,
each device must get a non-conflicting address before connecting it to the bus (e.g. using
the push-button addressing method). After addressing all devices, the remaining configu-
ration can be done over the bus using the default settings for baudrate (auto-baud) and
transmission mode for the Modbus master.

Overwriting the bus configuration over bus uses a timeout. If „1 = Load“ is not written into
Reg 768 within 30 seconds, all values are discarded.

Example: Table shows bus configuration registers before and after changing them over bus.

Reg.

Name

Pre-commissioning

New value (ex.)

764

MacAddress

46

12

765

Baudrate

0 = auto

1 = 9600

766

Transmission Mode

0 = 1-8-E-1

3 = 1-8-N-2

767

Termination

0 = Off

0 = Off

768

BusConfigCmd

0 = Ready

1 = Load

Содержание GLB111.9E/MO















Отзывы: