Side-Power SH SERIES, Руководство пользователя

Страница: 10 / 24

10
6032 3 2019
-
SEP user manual
Alarm Descriptions
EN
MC_0053
1. PPC520, PPC820, PPC800, PPC840
2. Buzzer is only activated when any device is sending thrust on the S-link bus.
"Err.
No."
Errors shown in display
"Auto
Reset"
"Ext. buzzer
activation at
Alert Level"
Description Action
1
Motor Overcurrent
2
(
²
)
, 3 Motor current too high. "Thruster must be serviced by author-
ized personnel, reset or power OFF/ON
PPC
(
¹
)
."
2
Motor Overtemp
Yes 2
(
²
)
, 3 "Motortemp has been over
120°C/248°F."
Motor cool down below 110°C /230°F.
3
Controller Overtemp 2
(
²
)
, 3 "PPC
(
¹
)
temp has been over
80°C/176°F."
PPC
(
¹
)
cool down below 45°C/113°F.
4
Controller Overtemp 2
(
²
)
, 3 "SR150000 temp has been over
80°C/176°F."
SR150000 cool down below 45°C
/113°F.
5
Low Voltage
2
(
²
)
, 3 Low motor voltage alarm when motor
is running.
12V thruster below 8.00V
24V thruster below 12.00V
Recharge battery, reset or power OFF/
ON device.
6
Thermoswitch Yes 2
(
²
)
, 3 Thermo switch input is activated and
there is an open circuit.
The thruster needs to cool down before
operating again.
7
IPC Error 2
(
²
)
, 3 Motor relay fault "Turn off thruster battery main switch.
Thruster must be serviced by author-
ized personel."
8
Critical Error 2
(
²
)
, 3 PPC
(
¹
)
output fail PPC
(
¹
)
must be sent for service.
9
Low Motor Current
2
(
²
)
, 3 Thruster uses no power Check thruster connections or motor
dead!
10
Motor Contactor
2
(
²
)
, 3 No current on motor relay coil. Check motor relay connections, short
circuit or relay dead!
11
System Error 2
(
²
)
, 3 Fatal error Device must be serviced by authorized
personel
12
No Communication 2
(
²
)
, 3 No communication with device Check S-Link cables and power con-
nections.
13
Motor Temp Sensor
2
(
²
)
, 3 Motor temperature sensor fail Check for an open circuit on the temp
sensor on the motor
14
Supply Voltage Fault
2
(
²
)
, 3 No power Check power connections
15
Fuse Blown 2
(
²
)
, 3 Fuse blown Replace fuse or check if main cable
from battery and main cable to thruster
has been switched
16
Manual Override
Yes 2
(
²
)
, 3 Main switch manually overridden Pull main switch
17
Motion OUT Fault 2
(
²
)
, 3 Retract obstructed while deploying Turn off all panels. Go for lower speed/
deeper water and retry.
18
Motion IN Fault 2
(
²
)
, 3 Retract obstructed while retracting Turn panel on and manually override
main switch. Remove obstruction and
try again.
Alarm Descriptions
EN
MC_0053
1. PPC520, PPC820, PPC800, PPC840
2. Buzzer is only activated when any device is sending thrust on the S-link bus.
"Err.
No."
Errors shown in display "Auto
Reset"
"Ext. buzzer
activation at
Alert Level"
Description Action
19
Actuator Fault 2
(
²
)
, 3 Actuator not getting any power "Check actuator connection or pow-
er to actuator. Reset alarm in alarm
menu on PJC 211/212/221/222 or
recycle power."
20
Pos.Sensor Fault 2
(
²
)
, 3 Retract position sensor fail Check position sensor cables and
for sensor damage.
21
In Service Mode Yes 2
(
²
)
, 3 "Retract controller in service mode. Switch
no. 4 is ON."
Check dipswitch setting on retract
control box.
22
High Oil Temp Yes 1, 2
(
²
)
, 3 "Hydraulic oil temperature is higher than
75°C /167°F."
"Stop running and wait for tempera-
ture to drop.
Check if cooling pump is running."
23
Low Oil Level 1, 2
(
²
)
, 3 Hydraulic oil lewel is to low Fill more hydraulic oil to the hydrau-
lic tank.
24
Warning Return Filter Yes 2
(
²
)
, 3 Return fi lter element requiered
replacing.
25
Warning Pressure Filter Yes 2
(
²
)
, 3 Pressure fi lter element requiered
replacing.
26
Warning High Speed Yes 1, 2
(
²
)
, 3 "WARNING! High Speed.
Stabilizer not active!"
27
Stabilizer Fault Yes 1, 2
(
²
)
, 3 Any Stabilizer alarm. See stabilizer panel for more info.
28
AC Motor Overtemp Yes 1, 2
(
²
)
, 3 "Hydraulic AC motor power pack over-
temp. Higher than
120°C/248°F."
Stop running and wait for tempera-
ture to drop.
29
AC Motor Sensor Fail 2
(
²
)
, 3 "Hydraulic AC motor power pack temp
sensor open curicuit"
Check sensor cables.
30
Temperature Warning Yes 2
(
²
)
, 3
(
²
)
High temperature warning. Warns that the motor temperature is
getting high.
31
Motor Overtemp Yes 1, 2
(
²
)
, 3 High temperature Alarm. See SAC manual for more details.
32
VFD Warning Yes 2
(
²
)
, 3 There is an warning from VFD. Check VFD for more details.
33
VFD Not Ready Yes 2
(
²
)
, 3 The VFD is not ready. Check VFD for more details.
34
VFD Fault 1, 2
(
²
)
, 3 VFD has an Alarm. Check VFD for more details.
35
Warning Low Voltage Yes 2
(
²
)
, 3
(
²
)
Low motor voltage warning when motor
is running.
12V thruster below 9.30V
24V thruster below 17.50V
36
Not Calibrated Yes 2
(
²
)
, 3 Shaft Not Calibrated See manual for how to calibrate.
37
VFD Com. Fault 2
(
²
)
, 3 No Modbus communication with VFD Check VFD Modbus cables and
power.
38
Cooling Fan Fault 2
(
²
)
, 3 Cooling fan stopped running, or running
too slow
Device must be sent for service
39
Interlock 2
(
²
)
, 3 S-link communication between PPC and
retract controller are missing
-Check PPC or retract controller has
power.
-Check S-Link connections to PPC
and retract controller.
-Check if not PPC or SR150000/
SR61242 is wrongly setup as SRP or
SRVP/SRLP.