manualshive.com logo in svg

SICK FX3-MOC1, Руководство по эксплуатации

Поделиться
Скачать
SICK FX3-MOC1 Скачать руководство пользователя страница 87

Table 79: Requirements for the SSI interface

Check sequence

Expected result

Result OK?

1.

Check the baud rates of both
OLM sensors in the Flexi Soft pro‐
gram and potentially also the
process controller.

Both SSI interfaces have different
transmission rates ranging from
100 kBaud to 400 kBaud.

Yes 

⃞

 No 

⃞

Baud rate of OLM sensor 1:
Baud rate of OLM sensor 2 (standard value: 167 kBaud):

Configuration

Table 80: Definition of the permitted position values

Check sequence

Expected result

Result OK?

1.

Check the position ranges
entered in the Flexi Soft program.

The position ranges that are not per‐
mitted (= not used) within the applica‐
tion have been determined and the
FX3-MOC1 module has been config‐
ured accordingly with the Flexi Soft
Designer software.

Yes 

⃞

 No 

⃞

17.1.2

Thorough check of the hardware requirements

Drive system

Table 81: Drive system

Check sequence

Expected result

Result OK?

1.

Check that the drive’s safe torque
off (STO) function and electrical
control comply with the require‐
ments of category 4, PL e (EN ISO
13849-1).

Compliance with the requirements for
category 4, PL e (EN ISO 13849-1) is
confirmed.

Yes 

⃞

 No 

⃞

Brake

Table 82: Brake

Check sequence

Expected result

Result OK?

1.

Check that the brake and electri‐
cal control comply with the
requirements of category 4, PL e
(EN ISO 13849-1).

Compliance with the requirements for
category 4, PL e (EN ISO 13849-1) is
confirmed or the risk assessment indi‐
cated that a brake is not required.

Yes 

⃞

 No 

⃞

External signal for requesting the safely limited speed (SLS)

Table 83: External signal for requesting the safely limited speed (SLS)

Check sequence

Expected result

Result OK?

1.

Check that the signal source and
electrical transmission path com‐
ply with the requirements of cate‐
gory 4, PL e (EN ISO 13849-1).

Compliance with the requirements for
category 4, PL e (EN ISO 13849-1) is
confirmed or an external signal is not
used to request the safely limited
speed (SLS).

Yes 

⃞

 No 

⃞

ANNEX 

17

8020941/12O9/2019-08-05 | SICK

O P E R A T I N G   I N S T R U C T I O N S | Safe Linear Positioning

87

Subject to change without notice

Содержание FX3-MOC1

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды