SICK 1 075 638 Скачать руководство пользователя страница 38

Страница: 38 / 70

Parameter

Factory setting

-1,000.0 m ... +1,000.0 m

-600.0 m

Teaching in the zero point

The current distance is taught in as a new zero point (reference point). When the analog
output is activated, the analog value is set to the center of the measuring range at this
distance (12 mA / 5 V).

Measurement

Default settings

Measured value offset

Teach in zero point

NOTE

This function can also be executed using a shortcut:

In the main display level, press and hold the pushbutton for > 3 seconds until
the relative distance value is set to 0.0 mm

Resetting the zero point

This resets the zero point to the center of the measuring range according to the factory
setting.

Measurement

Default settings

Measured value offset

Reset zero point

NOTE

This function can also be executed using a shortcut:

In the main display level, press and hold the pushbutton for > 6 seconds until
the relative distance value is set to the factory setting.

8.3.2.6

Action in case of incorrect measurements

If a distance measurement cannot be run, an error is output. Possible causes of the
error:

•

The measuring object is outside of the measuring range.

•

The light signal received by the device is not strong enough.

•

The laser is switched off.

You can configure the device behavior for the event that no measurement is possible.
The following options are available:

OPERATION VIA DISPLAY

O P E R A T I N G I N S T R U C T I O N S | OD1000

8019642/18JN/2020-07-01 | SICK

Subject to change without notice

Содержание 1 075 638







































































Результаты поиска

Содержание 1 075 638

Отзывы:

Похожие инструкции для 1 075 638

Бренды по названию

Популярные бренды

SICK 1 075 638, Руководство по эксплуатации

Результаты поиска

Содержание 1 075 638

Отзывы:

Похожие инструкции для 1 075 638

Бренды по названию

Популярные бренды