SIBS Fuso Canter Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 41

background image

MAN-059

8 FEB 2017

25

5.

Fit the vehicle interface harness:

a.

Open the top of the dash above the centre console.

b.

Connect the Deutsch end of the vehicle interface harness to the 6 pin connector on the SIBS® cabin harness.

c.

Connect the interface harness wires to the desired vehicle interlock wires behind the instrument cluster. Cut the
wires to the desired length.

d.

De-pin any unwanted wires from the interface harness.

Figure 14: Connection for interlocks behind the instrument cluster.

6.

Fit the OEM door harness 18-7008 (optional):

a.

The OEM door harness is supplied with the vehicle interface harness

–

simply connect the additional 3-pin Deutsch

connector to the SIBS® cabin harness located in the dash under the control box.

b.

Do not connect if ABT door proximity sensors are to be fitted.

Connect desired interlocks from SIBS
interface harness to OEM connectors

Interface harness connector

«
...
23
24
25
26
27
...
»

Содержание Fuso Canter










































Отзывы:

Нет отзывов

Похожие инструкции для Fuso Canter

Magliner H-1382

Бренд: U-Line Страницы: 6

Бренд: SAC Страницы: 30

Бренд: OEG Страницы: 20

Бренд: Moxy Страницы: 170

Бренд: Fronius Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды