Shuttle HOT-603 Скачать руководство пользователя | Manualshive

Страница: 7 / 37

background image

7

Hardware Configuration

Jumper Setting

Jumper pin headers show on right side
are used to configure system clock,
CPU multiplier and CPU voltages.

System Clock - JC1

JC1 is a 6-pins header jumper which
is used to adjust System Clock from
50MHz to 83 MHz.

CPU Multiplier - JP1, JP2 and JP3

JP1, JP2 and JP3 are 3-pins header
jumper which is used to adjust CPU core multiplier from 1.5X to 5.5X.

CPU Voltages

JPW1, JV2, JV3 and JV4 are used to adjust onboard voltages output from Switching
type regulators to CPU by inserting or removing mini jumper from pin headers.

Those hardware settings are made through the use of jumper caps to connect jumper
pins on the main board. The jumpers will be show graphically such as to connect
pins 3&4 and 5&6, and to connect pins 1&2 and 3&4 for six pin jumpers.
Jumpers will be show graphically such as to connect pins 2&4 and to
connect pins 3&4 for four pin jumpers.

Jumpers with two pins will be shown as for Short (On) and for Open (Off).
To connect the pins, simply place a plastic jumper cap over the two pins as dia-
gramed.

2

2

«
...
5
6
7
8
9
...
»

Содержание HOT-603






































Отзывы:

Нет отзывов

Похожие инструкции для HOT-603

Бренд: V2 ELETTRONICA Страницы: 12

Бренд: Digital Equipment Страницы: 98

Бренд: AKM Страницы: 45

Бренд: WIN Enterprises Страницы: 82

Бренд: Phytec Страницы: 128

Бренд: Sapphire Audio Страницы: 50

Бренд: National Semiconductor Страницы: 22

Бренд: Gigabyte Страницы: 116

Бренд: Biostar Страницы: 31

Бренд: Pentair Страницы: 4

Бренд: Intel Страницы: 92

Бренд: TYAN Страницы: 96

Бренд: ASROCK Страницы: 212

Coccinella Master Plus

Бренд: SEA Страницы: 2

Бренд: CAME Страницы: 8

Бренд: DFI Страницы: 73

Бренд: Texas Instruments Страницы: 7

Бренд: Supero Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды