Shuttle HOT-603 Скачать руководство пользователя | Manualshive

Страница: 30 / 37

background image

30

PCI Configuration Setup

PNP OS Installed

When this item is set to Yes, it will allow the PnP OS(Windows 95) control the
system resources except PCI devices and PnP boot devices.
Default setting is

No

.

Resources Controlled By

The Award Plug and Play BIOS has the capability to automatically configure all of the
boot and Plug and Play compatible devices. However, this capability means abso-
lutely nothing unless you are using a Plug and Play operating system as Windows 95.

Reset Configuration Data

This item allows you to determine whether to reset the configuration data or not.

IRQ 3/4/5/7/9/10/11/12/14/15, assigned to

These items allow you to determine the IRQ assigned to the ISA bus and is not
available for PCI slot.

Choices are

Legacy ISA

and

PCI/ISA PnP

.

DMA 0/1/3/5/6/7 assigned to

These items allow you to determine the DMA assigned to the ISA bus and is not
available for PCI slot.

Choices are

Legacy ISA

and

PCI/ISA PnP

.

«
...
28
29
30
31
32
...
»

Содержание HOT-603






































Отзывы:

Нет отзывов

Похожие инструкции для HOT-603

Бренд: P&E Microcomputer Systems Страницы: 38

Бренд: Atmel Страницы: 16

Бренд: Zida Страницы: 28

Бренд: ASROCK Страницы: 2

C5535 DSPShield

Бренд: Texas Instruments Страницы: 49

Бренд: BESTEK Страницы: 47

Бренд: Gigabyte Страницы: 87

Бренд: Supero Страницы: 107

Бренд: Diamond Systems Страницы: 112

Бренд: Gigabyte Страницы: 40

Бренд: Supero Страницы: 92

Бренд: VIA Technologies Страницы: 81

Бренд: BOSER Technology Страницы: 38

Бренд: Semtech Страницы: 16

Бренд: Gigabyte Страницы: 88

Бренд: Acconeer Страницы: 14

Бренд: ETOP Страницы: 68

Бренд: Gigabyte Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды