Shuttle HOT-603 Скачать руководство пользователя | Manualshive

Страница: 23 / 37

background image

23

Drive A type/Drive B type

This item specifies the types of floppy disk drive A or drive B that has been installed in
the system.

Video

This item selects the type of adapter used for the primary system monitor that must
matches your video display card and monitor. Although secondary monitors are
supported, you do not have to select the type in Setup.

Error halt

This item determines if the system will stop, when an error is detected during power
up.

Memory

This item is display-only. It is automatically detected by POST (Power On Self Test)
of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory
installed in the system. The value of the base memory is typically 512K for systems
with 512K memory installed on the mainboard, or 640K for systems with 640K or
more memory installed on the mainboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST. This
is the amount of memory located above 1MB in the CPU's memory address map.

«
...
21
22
23
24
25
...
»

Содержание HOT-603






































Отзывы:

Нет отзывов

Похожие инструкции для HOT-603

Бренд: hager Страницы: 4

Бренд: Aaeon Страницы: 30

ML501MicroBlaze

Бренд: Xilinx Страницы: 46

Бренд: Arbor Technology Страницы: 86

STEVAL-ISB042V1

Бренд: ST Страницы: 26

VIOTECH 3100 PLUS - BIOS

Бренд: Biostar Страницы: 41

Бренд: MATSONIC Страницы: 39

Бренд: VIA Technologies Страницы: 81

Бренд: Rosch Computer Страницы: 43

Бренд: Biostar Страницы: 68

Бренд: Avalue Technology Страницы: 60

Бренд: Sleipner Страницы: 24

iEi ROCKY-4782E2V

Бренд: ICP Electronics Страницы: 52

Бренд: DFI Страницы: 121

Бренд: ASROCK Страницы: 5

Бренд: ASROCK Страницы: 100

Бренд: ASROCK Страницы: 42

Бренд: Artesyn Embedded Technology Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды