Shuttle HOT-603 Скачать руководство пользователя страница 26

Страница: 26 / 37

Chipset Features Setup

NOTE:

Those item on this page are concering AMD-640 chipset timing, please do not try to
adjust by yourself unless you are familiar with them.

Auto Configuration

This item auto configures the item of DRAM Timing Control.

DRAM Timing

Control

will be set to "Auto" when this item set to

60 ns

70 ns

DRAM Timing

Control

may be set to "Normal", "Medium", "Fast" or "Turbo" when this item set to

Disabled.

DRAM Timing Control

This item set the DRAM Read/Write timings that the system uses. The options are
"Normal", "Medium", "Fast", "Turbo" or "Disabled".

Video BIOS Cacheable

This item allows the user to set the video BIOS C000~C7FF areas that are cacheable or
non-cacheable.

System BIOS Cacheable

This item allows the user to set the system BIOS F000~FFFF areas that are cacheable
or non-cacheable.

Memory Hole At 15M-16M

In order to improve performance, some space in memory can be reserved for ISA
cards. This memory must be mapped into the memory space below 16 MB.

Содержание HOT-603






































Результаты поиска

Содержание HOT-603

Отзывы:

Похожие инструкции для HOT-603

Бренды по названию

Популярные бренды

Shuttle HOT-603, Руководство пользователя

Результаты поиска

Содержание HOT-603

Отзывы:

Похожие инструкции для HOT-603

Бренды по названию

Популярные бренды