Shuttle HOT-603 Скачать руководство пользователя | Manualshive

Страница: 14 / 37

background image

14

USB1, USB2 - USB connectors

The main board provides two sets USB (Universal Serial Bus)
connectors - USB1 and USB2 for USB devices use.

IR1, IR2 - Infrared module
connectors

The main board provides a 5-pin infrared and
fast infrared connectors as an optional
infrared module for wireless transmitting and
receiving.

FAN1- 12V cooling fan power con-
nector

The main board provides an onboard 12V cooling fan power
connector which provide maximum 100
mAMP(1.2W) current each for CPU cooling fan.
Depending on the fan maker, the wiring and plug
may be different. The red wire should be con-
nected to +12V and black wire should be con-
nected to ground (GND).

J4 - Green LED connector

J4 is a 3-pin Green LED connector, the user can connect a LED
on it to display power management status.

PWRBTN1 - ATX Power Switch But-
ton Connector

(Available only when ATX power supply is used).

The system power can be controlled by a momentary switch
connector. Pushing the switch button will turn the system off .

Note:

When a AT Power Supply is used to HOT-603,
please do not connect any momentary switch to
PWRBTN1.

AT and ATX Power connectors

The main board provides both AT and ATX Power con-
nector. ATX power supports soft power on/off function.

«
...
12
13
14
15
16
...
»

Содержание HOT-603






































Отзывы:

Нет отзывов

Похожие инструкции для HOT-603

Бренд: Texas Instruments Страницы: 8

Бренд: AXIOMTEK Страницы: 2

Бренд: Linear Technology Страницы: 6

Бренд: Biostar Страницы: 47

Бренд: Abit Страницы: 72

Бренд: Infineon Страницы: 24

Бренд: Texas Instruments Страницы: 17

Бренд: JETWAY Страницы: 70

Freescale MC9S08MM128

Бренд: NXP Semiconductors Страницы: 12

Бренд: Intel Страницы: 26

Бренд: K&B Страницы: 6

Бренд: ON Semiconductor Страницы: 2

Бренд: Protek Страницы: 2

Бренд: Hitachi Страницы: 56

Compute Blade 2000

Бренд: Hitachi Страницы: 52

SH7760 Solution Engine2

Бренд: Hitachi Страницы: 138

Compute Blade 2500

Бренд: Hitachi Страницы: 154

Бренд: Motorola Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды