Shuttle HOT-603 Скачать руководство пользователя | Manualshive

Страница: 20 / 37

background image

20

Main Menu

Standard CMOS setup

This setup page includes all items in a standard compatible BIOS.

BIOS features setup

This setup page includes all items of Award special enhanced features.

Chipset features setup

This setup page includes all items of chipset features.

Power Management Setup

This setup page includes all items of Power Management features.

PnP/PCI Configuration setup

This item specifies the value (in units of PCI bus blocks) of the latency timer for the
PCI bus master and the IRQ level for PCI device. Power-on with BIOS defaults

Load BIOS Defaults

BIOS defaults loads the values required by the System for the maximum performance.
However, you can change the parameter through each Setup Menu.

Load Setup Defaults

Setup defaults loads the values required by the system for the O.K. performance.
However, you can change the parameter through each Setup Menu.

«
...
18
19
20
21
22
...
»

Содержание HOT-603






































Отзывы:

Нет отзывов

Похожие инструкции для HOT-603

RouterBOARD 411

Бренд: 4gon Страницы: 2

ASC Bridge Board

Бренд: Lattice Semiconductor Страницы: 25

Бренд: TYAN Страницы: 82

661FX7MJ Series

Бренд: Foxconn Страницы: 81

TA870 PLUS - SETUP 2

Бренд: Biostar Страницы: 67

H55M-LE - - 01-2010

Бренд: ASROCK Страницы: 181

Бренд: Vector Страницы: 73

Бренд: Microchip Technology Страницы: 35

Бренд: Texas Instruments Страницы: 19

Бренд: Analog Devices Страницы: 16

Бренд: JETWAY Страницы: 46

Бренд: MSI Страницы: 445

Бренд: Advantech Страницы: 136

Бренд: ECS Страницы: 131

Бренд: NXP Semiconductors Страницы: 138

Бренд: DFI Страницы: 183

Бренд: Texas Instruments Страницы: 17

Бренд: California Instruments Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды