Shuttle HOT-603 Скачать руководство пользователя | Manualshive

Страница: 1 / 37

background image

FCC Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy. If not installed and used properly, in strict accor-
dance with the manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help and for additional suggestions.

The user may find the following booklet prepared by the Federal Communications Commission helpful “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office.
Washington, DC 20402, Stock 004-000-00345-4

FCC Warning

The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.

Note : In order for an installation of this product to maintain compliance with the limits for a Class B device, shielded
cables and power cord must be used.

CE Notice:

Following standards were applied to this product, in order to achieve compliance with the electromagnetic
compatibility :

- Immunity in accordance with EN 50082-1: 1992
- Emissions in accordance with EN 55022: 1987 Class B.

NOTICE

Copyright 1997.

All Right Reserved

Manual Ver 1.1

All information, documentation, and specifications contained in this manual are subject to change without prior
notification by the manufacturer.

The author assumes no responsibility for any errors or omissions which may appear in this document nor does
it make a commitment to update the information contained herein.

TRADEMARKS

All the brands and product names referred to in this manual are trademarks or registered trademarks of their
respective holders.

M87

1
2
3
...
»

Содержание HOT-603






































Отзывы:

Нет отзывов

Похожие инструкции для HOT-603

Бренд: Acer Страницы: 12

Бренд: MSI Страницы: 92

Бренд: CIRCUIT DESIGN Страницы: 9

Бренд: IEI Technology Страницы: 15

Бренд: JETWAY Страницы: 49

Z270 Gaming Pro Carbon Motherboard

Бренд: MSI Страницы: 92

Бренд: ST Страницы: 15

Бренд: MSI Страницы: 30

Бренд: Nematron Страницы: 47

Бренд: Avalue Technology Страницы: 82

Бренд: Ublox Страницы: 21

Бренд: Shuttle Страницы: 81

Бренд: Epcom Страницы: 8

880GM-LE - V1.0

Бренд: ASROCK Страницы: 60

Бренд: Gigabyte Страницы: 87

Бренд: TYAN Страницы: 37

Бренд: Gigabyte Страницы: 120

Бренд: Zeal-All Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды