Shur-Co AutoGate Скачать руководство пользователя

Страница: 3 / 16

AutoGate™

P/N 1128479 Rev. A

Thank you for buying this product from Shur-Co

. We appreciate your

confidence in our products. Please read and thoroughly understand

this manual before installing and/or operating this system.
Pay particular attention to important safety and operating instructions,

as well as warnings and cautions. The hazard symbol is used to

alert users to potentially hazardous conditions and is followed by cau

tion, warning or danger messages.
Failure to READ AND FOLLOW INSTRUCTIONS could result in fail

ure of your system and/or personal injury. Your trailer requirements

may, however, call for minor variations to these instructions.
Please inspect your system periodically. Repair or replace worn or

damaged parts to your system.

QUESTIONS? CALL OUR HELP LINE:

1-866-748-7435

MON-FRI 8 AM-5 PM CENTRAL TIME

Mounting Hardware

............................................................................1

System Components ..........................................................................2

Stop Plate and Brackets Installation

...............................................3-4

Control Box Installation

.......................................................................

Actuator Installation

............................................................................6

Trickle Charger Installation

.................................................................7

Final Adjustments

...............................................................................8

Replacement Parts

.............................................................................9

We at Shur-Co

are concerned with your safety and the safety of all

those operating this system. Therefore, we have provided safety de

cals at various locations on your system. Keep decals as clean as pos

sible at all times. Replace any decal that has become worn or dam

aged, painted over or otherwise difficult to read. Replacement decals

are available through Shur-Co

dealers.

TABLE OF CONTENTS

MESSAGE TO OWNERS

SAFETY

1. Electric Drill

2. Air or Electric Impact Wrench

3. Sockets - 5/16", 1/2", 9/16", 17mm

4. Nut Driver - 5/16"

5. Hand Wire Crimper

6. Wire Stripper

7. Voltmeter

8. Wrenches - 1/2", 9/16", 17mm

9. Drill Bits - 1/4", 5/16", 3/8"

TOOLS REQUIRED

1. Always wear safety glasses during installation.
2. Keep body and clothing clear of moving parts.

3. No other use of this system is authorized,

except as designed.

SAFETY INSTRUCTIONS

Содержание AutoGate

















Результаты поиска

Содержание AutoGate

Отзывы:

Похожие инструкции для AutoGate

Бренды по названию

Популярные бренды

Shur-Co AutoGate, Руководство пользователя

Результаты поиска

Содержание AutoGate

Отзывы:

Похожие инструкции для AutoGate

Бренды по названию

Популярные бренды