background image

 

 

Never remove warning or informative labels from the unit. 

 

Never use anything to cover the ground contact of the (optional) battery charger. 

 

Never look directly into the light source. 

 

Never leave any cables lying around. 

 

Never use the device during thunderstorms, unplug the device immediately. 

 

Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within 
children’s reach, as they are potential sources of danger. 

 

Do not insert objects into air vents. 

 

Do not open the device and do not modify the device. 

 

Do not shake the device. Avoid brute force when installing or operating the device. 

 

Do not switch the device on and off in short intervals, as this would reduce the system’s life. 

 

Only operate the device after having familiarized with its functions. 

 

Avoid flames and do not put close to flammable liquids or gases. 

 

Always allow free air space of at least 50 cm around the unit for ventilation. 

 

Make sure that the device is not exposed to extreme heat, moisture or dust. 

 

If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, 
due to cracks or deep scratches. 

 

If device is dropped or struck, switch off the device. Have a qualified engineer inspect for 
safety before operating. 

 

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), 
do not switch it on immediately. The arising condensation water might damage your device. 
Leave the device switched off until it has reached room temperature. 

 

If your Showtec device fails to work properly, discontinue use immediately. Pack the unit 
securely (preferably in the original packing material), and return it to your Showtec dealer for 
service. 

 

For adult use only. The device must be installed out of the reach of children. Never leave the 
unit running unattended. 

 

The user is responsible for correct positioning and operating of the Eventspot 1900 mkII. The 
manufacturer will not accept liability for damages caused by the misuse or incorrect 
installation of this device. 

 

Repairs, servicing and electric connection must be carried out by a qualified technician. 

 

WARRANTY: Till one year after date of purchase. 

 
 
 
 
 
 

 

CAUTION ! EYEDAMAGES !. 

Avoid looking directly into the light source. 

(meant especially for epileptics) !

 

 

Содержание Eventspot 1900 MKII





























Отзывы: