Shop fox W1867 Скачать руководство пользователя страница 14

Страница: 14 / 60

-12-

Model W1867/W1868/W1869 (For Machines Mfd. Since 11/18)

W1868/W1869.220V.

Circuit.Requirements

This machine must be connected to the correct size and

type of power supply circuit, or fire or electrical damage

may occur. Read through this section to determine if an

adequate power supply circuit is available. If a correct

circuit is not available, a qualified electrician MUST install

one before you can connect the machine to power.

A power supply circuit includes all electrical equipment

between the breaker box or fuse panel in the building

and the machine. The power supply circuit used for

this machine must be sized to safely handle the full-

load current drawn from the machine for an extended

period of time. (If this machine is connected to a circuit

protected by fuses, use a time delay fuse marked D.)

Circuit.Requirements

This machine is prewired to operate on a power supply

circuit that has a verified ground and meets the following

requirements:

Circuit.Type

....................

220V,.60.Hz,.Single-Phase

Circuit.Size.(W1868)

................................

15.Amps

Circuit.Size.(W1869)

................................

20.Amps

Plug/Receptacle.(W1868)

.......................

NEMA.6-15

Plug/Receptacle.(W1869)

.......................

NEMA.6-20

Full-Load.Current.Rating

The full-load current rating is the amperage a machine

draws at 100% of the rated output power. On machines

with multiple motors, this is the amperage drawn by the

largest motor or sum of all motors and electrical devices

that might operate at one time during normal operations.

Full-Load.Current.Rating.(W1868)..................9.Amps

Full-Load.Current.Rating.(W1869)................ 15.Amps

The machine must be properly set up

before it is safe to operate. DO NOT

connect this machine to the power

source until instrtucted to do so later

in this manual.

Incorrectly. wiring. or. grounding. this.

machine.can.cause.electrocution,.fire,.

or.machine.damage..To.reduce.this.risk,.

only.an.electrician.or.qualified.service.

personnel. should. do. any. required.

electrical.work.on.this.machine.

NOTICE

The.circuit.requirements.listed.in.this.

manual. apply. to. a. dedicated. circuit—

where.only.one.machine.will.be.running.

at. a. time.. If. this. machine. will. be.

connected. to. a. shared. circuit. where.

multiple.machines.will.be.running.at.the.

same.time,.consult.with.an.electrician.

to. ensure. that. the. circuit. is. properly.

sized.for.safe.operation.

Содержание W1867





























































Результаты поиска

Содержание W1867

Отзывы:

Похожие инструкции для W1867

Бренды по названию

Популярные бренды

Shop fox W1867, Руководство пользователя

Результаты поиска

Содержание W1867

Отзывы:

Похожие инструкции для W1867

Бренды по названию

Популярные бренды