Shop fox W1867 Скачать руководство пользователя страница 13

Страница: 13 / 60

-11-

Model W1867/W1868/W1869 (For Machines Mfd. Since 11/18)

Grounding.Requirements

This machine MUST be grounded. In the event of certain

types of malfunctions or breakdowns, grounding provides

a path of least resistance for electric current to travel—in

order to reduce the risk of electric shock.

Improper connection of the equipment-grounding wire will

increase the risk of electric shock. The wire with green

insulation (with/without yellow stripes) is the equipment-

grounding wire. If repair or replacement of the power

cord or plug is necessary, do not connect the equipment-

grounding wire to a live (current carrying) terminal.

Check with a qualified electrician or service personnel

if you do not understand these grounding requirements,

or if you are in doubt about whether the tool is

properly grounded. If you ever notice that a cord or

plug is damaged or worn, disconnect it from power, and

immediately replace it with a new one.

This machine is equipped with a power cord with an

equipment-grounding wire and NEMA 5-15 grounding

plug (see figure). The plug must only be inserted into

a matching receptacle that is properly installed and

grounded in accordance with local codes and ordinances.

For.110V.Connection

The machine must be properly set up

before it is safe to operate. DO NOT

connect this machine to the power

source until instrtucted to do so later

in this manual.

Extension.Cords

We do not recommend using an extension cord with

this machine. Extension cords cause voltage drop, which

may damage electrical components and shorten motor

life. Voltage drop increases with longer extension cords

and smaller gauge sizes (higher gauge numbers indicate

smaller sizes).

Any extension cord used with this machine must contain a

ground wire, match the required plug and receptacle, and

meet the following requirements:

Minimum.Gauge.Size.................................. 12.AWG

Maximum.Length.(Shorter.is.Better).................50.ft.

Grounding Pin

Neutral Hot

5-15 PLUG

GROUNDED

5-15 RECEPTACLE

110V

Figure.4.

Typical 110V plug & receptacle.

No. adapter. should. be. used. with. the.

required.plug..If.the.plug.does.not.fit.

the.available.receptacle.or.the.machine.

must. be. reconnected. to. a. different.

type.of.circuit,.the.reconnection.must.

be.made.by.an.electrician.or.qualified.

service. personnel. and. it. must. comply.

with.all.local.codes.and.ordinances.

Содержание W1867





























































Результаты поиска

Содержание W1867

Отзывы:

Похожие инструкции для W1867

Бренды по названию

Популярные бренды

Shop fox W1867, Руководство пользователя

Результаты поиска

Содержание W1867

Отзывы:

Похожие инструкции для W1867

Бренды по названию

Популярные бренды