background image

-40-

Model W1867/W1868/W1869 (For Machines Mfd. Since 11/18)

M

A

INTE

N

A

N

CE

Cleaning.Canister.Filter

This dust collector uses a handle and internal paddles 

to remove excess dust and debris from the filter pleats. 

Move the handle back and forth through its range of 

motion to knock dust into the filter bag. Dispose of the 

bag when dust fills it about 

1

2

 full.

After extended use, the filter should be replaced, or 

thoroughly cleaned by hand.

To.clean.canister.filter.by.hand,.do.these.steps:

1.

  DISCONNECT MACHINE FROM POWER!

2.

 Remove bag clamp, filter bag, and canister filter (see 

Figure.58

).

3.

 Rinse filter with water in an appropriate outdoor 

location. 

 

IMPORTANT:.

DO NOT use compressed air to clean or 

dry the filter, as this can spread fine dust into the 

air and damage filter fibers.

Item(s).Needed.

Qty

Drum Bag D4894 (Models W1867, W1868) ..................1

Drum Bag D4896 (Model W1869) .............................1

To.remove.and.replace.collection.drum.bag,.do.these.

steps:

1.

  DISCONNECT MACHINE FROM POWER!

2.

  Lift drum lock handle to lower collection drum onto 

casters (see 

Figure.57

).

3.

  Release both latches on sides of drum, then roll 

drum clear of drum lid (see 

Figure.57

).

4.

  Lift bag out of drum and dispose of contents.

 

IMPORTANT:

 To contain wood dust and minimize risk 

of exposure, tie bag closed before disposal. 

5.

  Place new dust bag inside collection drum, and fold 

excess bag length over top of drum.

6.

  Move collection drum under lid and latch it closed.

7.

  Press drum lock handle down to lift collection drum 

off casters for operation.

Figure.57.

 Collection drum bag 

components.

Drum Lid

Drum Lock 

Handle

Drum Bag

Latch 

(1 of 2)

Figure.58.

 Filter bag components.

Canister 

Filter

Bag 

Clamp

Filter 

Bag

4.

  Allow filter to air dry only. DO NOT 

use heat.

Содержание W1867





























































Отзывы:

Похожие инструкции для W1867