Shindaiwa DGK15FL Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 54

background image

18

5-7. Fuel Piping Switch (3Way Fuel Valve)

Change the three-way fuel valve to switch to supply
fuel from the external tank. In that case, the internal
fuel tank will not be used.

(1) If using the internal fuel tank

Change the lever of the three-way fuel valve turned to
the “B” side to supply fuel from the internal tank. It is
turned to the “B” side when the generator is shipped
from the factory.

< Note >



When disconnecting piping from the external tank,
turn the lever to the “B” side, and attach the bundled
plug (R1/2”) to the external tank fuel inlet/return.

(2) If using an external fuel tank

Connect hoses from the external fuel tank
to the external fuel inlet and the external
fuel return.
Change the lever of the 3way fuel valve to
the “A” side to supply fuel from the
external tank.
Refer to “

9-6. Connecting with External

Fuel Tank

” for corresponding procedures.

6-1. Transport Procedures

CAUTION : FIRE



Always make sure that the engine is stopped when working on piping.



Always be sure to wipe up any spilled fuel.



After working on the piping, check that there is no fuel leakage.

WARNING : INJURY



Always be sure to use “Lifting Hook” when lifting up the generator. Using other parts
when lifting up the generator could cause the result of falling.



No persons should ever be under a lifted generator.

CAUTION : INJURY



Always be sure to use “Lifting Hook” when lifting up the generator, and lift slowly
and vertically.



Personnel performing lifting work must wear protective gear such as helmets, safety
shoes and gloves.



Do not move the generator during operation.

6. Transport/Installation

3Way Fuel
Valve

External
Fuel Inlet

External
Fuel Return

Position B

Position A

Return Side

Inlet Side

Return Side

Inlet Side

«
...
19
20
21
22
23
...
»

Содержание DGK15FL























































Отзывы:

Нет отзывов

Похожие инструкции для DGK15FL

Бренд: Baofeng Страницы: 7

Бренд: Jabra Страницы: 2

aXis CONTROLLER

Бренд: Champion Страницы: 45

Бренд: Grundig Страницы: 8

Бренд: Pulsar Страницы: 39

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 80

Бренд: Toshiba Страницы: 76

Бренд: Toshiba Страницы: 100

Бренд: Toshiba Страницы: 100

Бренд: Toshiba Страницы: 100

Бренд: ELBE Страницы: 20

Бренд: GÜDE Страницы: 57

Бренд: BK Radio Страницы: 37

Бренд: Roadstar Страницы: 2

Бренд: VeGue Страницы: 2

Бренд: Chicago Electric Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды